84510-30 is a shielded armored Seismoprobe cable with a 30 ft length, two-socket female connector and terminal lugs. Check the mating sensor and cable route before replacement.
Item NO.:
84510-30Order(MOQ):
1Product Origin:
USALead Time：
2 daysBrand/ Manufacturer:
Bently NevadaDimensions:
30 ft cable assemblyWeight:
Exact configured weight to be confirmedCountry of Origin: :
USADescription:
84510-30 | Armored Transducer CableVERIFIED PRODUCT CONFIGURATION
84510-30 is a shielded armored Seismoprobe cable with a 30 ft length, two-socket female connector and terminal lugs. Check the mating sensor and cable route before replacement.
CONFIGURATION AT A GLANCE
SYSTEM CONFIGURATION
Confirm the exact part number, mating hardware, cable or probe family, monitoring channel and installed configuration before replacement.
OFFICIAL PRODUCT FEATURES
DIRECT SALES CONTACT
Send the complete part number, required quantity, destination and installed configuration for quotation and availability checking.
PRODUCT OVERVIEW
84510-30 is a shielded armored Seismoprobe cable with a 30 ft length, two-socket female connector and terminal lugs. Check the mating sensor and cable route before replacement.
PRODUCT LIFECYCLE STATUS
Current Baker Hughes documentation identifies the applicable Seismoprobe interconnection cables family. Confirm the complete 84510-30 ordering code and approval scope before procurement or replacement.
Compare the sensor connector drawing and pin assignment with the two-socket female end. A matching number of contacts alone does not establish mechanical compatibility.
No. The cable ordering table specifies feet. Plan the route for 30 ft, including service access and termination allowance; do not procure a 30 m cable as an equivalent.
Consider this construction where the cable route needs mechanical protection. Assess bends, supports and moving parts separately; armor is not permission to crush the lead or use it as a load-bearing member.
The instrument end has lugs, not a BNC plug. Compare the monitor terminal arrangement and approved wiring instructions before ordering an adapter or choosing another cable.
Verify conductor continuity, terminal security and the specified shield arrangement with the system isolated as required. Compare the restored signal with the recorded baseline before blaming the transducer.
Inspect the armor along the route, both terminations and the part-number marking. Photograph damaged armor, pulled lugs or a loose connector before accepting the assembly into MRO stock.
No. Sensor and cable limits are separate. Request the applicable rating for the offered 84510 assembly and check the hottest part of the planned cable route.
Specify 84510-30, the installed sensor connector, monitor terminal details, route length and exposure conditions. Include photos of both ends so a visually similar lead is not substituted.
OFFICIAL MANUFACTURER DOCUMENTS
Use official Bently Nevada sources for the exact Seismoprobe interconnection cables configuration. Confirm the complete part number and installed-system requirements before replacement.
Two-page model-specific manual covering exact configuration, product reference data, application guidance and procurement checks.
OPEN PRODUCT MANUAL →OFFICIAL DATASHEETManufacturer family document used to verify the displayed ordering configuration.
OPEN BENTLY NEVADA SUPPORT →SEE THE ACTUAL PRODUCT BEFORE YOU BUY
Ask for current product photos, the complete installed nameplate, product identification and connection details, packaging and visible condition. Verify that the supplied unit carries the exact 84510-30 part number.
EMAIL : [email protected]WHATSAPP/WECHAT : +86-18020776786MODEL IDENTIFICATION
| Specification | Official identification / verification note |
|---|---|
| Part number | 84510-30 |
| Manufacturer | Bently Nevada |
| Product family | Seismoprobe interconnection cables |
| Product type | Armored Transducer Cable |
| Length option 30 | 30 ft (9.144 m) |
| Conductors | 2-wire shielded, 22 AWG (0.5 mm²) |
| Mechanical protection | Armored cable |
| Sensor end | 2-socket female connector |
| Instrument end | Terminal lugs |
| Published family length range | 3 to 70 ft; this order is 30 ft |
| Country of origin | USA |
SEE THE ACTUAL PRODUCT BEFORE YOU BUY
Ask for current product photos, the complete installed nameplate, product identification and connection details, packaging and visible condition. Verify that the supplied unit carries the exact 84510-30 part number.
EMAIL : [email protected]WHATSAPP/WECHAT : +86-18020776786WHY BUY FROM MOORE AUTOMATION
Quick Quote
Fast response to complete part-number enquiries.
Global Delivery
Worldwide shipping options for industrial automation components.
Actual Product Verification
Current photos, nameplate images or inspection videos where available.
Technical Support
Support with product identification and installed-configuration verification.
CUSTOMER VOICES
Bought an ABB panel view from Moore last month but the signal light wouldn't turn on at first... They jumped on a video call with us immediately to guide us through troubleshooting. We talked through it a lot, but we finally got it fixed. Really fast and helpful after-sales support.
It was a very nice and good experience working with Moore. Specially with sales manager Sandy is very polite, skillful and knows everything about the product. Prices are very competitive, have big inventory of products with prompt lead time. Would like to work for a very long time.
Tel : +8618020776786
Whatsapp & Wechat : +8618020776786
Email : [email protected]
1 Year Warranty
