9200-06-01-11-04 is a two-wire velocity transducer with a top connector, isolated M10 x 1 base and ATEX/IECEx option. Its 06 selection has a 10 Hz minimum operating frequency.
Item NO.:
9200-06-01-11-04Order(MOQ):
1Product Origin:
USALead Time：
2 daysBrand/ Manufacturer:
Bently NevadaDimensions:
Typical height 102 mm; diameter 41 mmWeight:
300 g typical; exact supplied weight to be verifiedCountry of Origin: :
USADescription:
9200-06-01-11-04 | Seismoprobe Velocity TransducerVERIFIED PRODUCT CONFIGURATION
9200-06-01-11-04 is a two-wire velocity transducer with a top connector, isolated M10 x 1 base and ATEX/IECEx option. Its 06 selection has a 10 Hz minimum operating frequency.
CONFIGURATION AT A GLANCE
SYSTEM CONFIGURATION
Confirm the exact part number, mating hardware, cable or probe family, monitoring channel and installed configuration before replacement.
OFFICIAL PRODUCT FEATURES
DIRECT SALES CONTACT
Send the complete part number, required quantity, destination and installed configuration for quotation and availability checking.
PRODUCT OVERVIEW
9200-06-01-11-04 is a two-wire velocity transducer with a top connector, isolated M10 x 1 base and ATEX/IECEx option. Its 06 selection has a 10 Hz minimum operating frequency.
PRODUCT LIFECYCLE STATUS
Current Baker Hughes documentation identifies the applicable 9200 Seismoprobe family. Confirm the complete 9200-06-01-11-04 ordering code and approval scope before procurement or replacement.
No. The moving-coil transducer measures absolute vibration of its bearing-housing, casing or structural mounting point. Do not substitute it for a proximity channel measuring shaft motion relative to the bearing.
Its selected minimum operating frequency is 10 Hz. Compare the required measurement band with the documented response; use engineering review when important machine components lie below that limit.
The ordering option is 0° ±100°. The orientation figure defines 0° as vertical when viewed from the machine driver end; record the actual mounting direction before installation.
The selected approval option requires an isolated base. Confirm the M10 x 1 interface and isolation arrangement against the mounting drawing instead of substituting an ordinary threaded base.
No. Connector option 01 specifies top mount without cable. Order a compatible cable separately and allow access above the sensor for the mating connection.
The Seismoprobe uses moving-coil technology and needs no external power for its velocity signal. Verify that the receiving channel is configured for the documented sensor output, not an unrelated powered transducer.
No. The ATEX/IECEx marking and applicable safe-use conditions can impose a lower limit. Verify the certificate, ambient temperature and complete installation before approving hazardous-area service.
Document sensor orientation, mounting condition, terminal polarity and channel scaling. Check the measured response against the previous baseline and site acceptance criteria before restoring protection functions.
OFFICIAL MANUFACTURER DOCUMENTS
Use official Bently Nevada sources for the exact 9200 Seismoprobe configuration. Confirm the complete part number and installed-system requirements before replacement.
Two-page model-specific manual covering exact configuration, product reference data, application guidance and procurement checks.
OPEN PRODUCT MANUAL →OFFICIAL DATASHEETManufacturer family document used to verify the displayed ordering configuration.
OPEN BENTLY NEVADA SUPPORT →SEE THE ACTUAL PRODUCT BEFORE YOU BUY
Ask for current product photos, the complete installed nameplate, product identification and connection details, packaging and visible condition. Verify that the supplied unit carries the exact 9200-06-01-11-04 part number.
EMAIL : [email protected]WHATSAPP/WECHAT : +86-18020776786MODEL IDENTIFICATION
| Specification | Official identification / verification note |
|---|---|
| Part number | 9200-06-01-11-04 |
| Manufacturer | Bently Nevada |
| Product family | 9200 Seismoprobe |
| Product type | Seismoprobe Velocity Transducer |
| Angle / frequency option 06 | 0° ±100°; minimum 10 Hz |
| Connector option 01 | Top mount, no cable |
| Mounting base option 11 | Isolated circular M10 x 1 |
| Approval option 04 | ATEX / IECEx; apply certificate conditions |
| Nominal sensitivity | 20 mV/mm/s (500 mV/in/s), ±5% under stated conditions |
| Standard temperature range | -29°C to +121°C; approval limits also apply |
| Country of origin | USA |
SEE THE ACTUAL PRODUCT BEFORE YOU BUY
Ask for current product photos, the complete installed nameplate, product identification and connection details, packaging and visible condition. Verify that the supplied unit carries the exact 9200-06-01-11-04 part number.
EMAIL : [email protected]WHATSAPP/WECHAT : +86-18020776786WHY BUY FROM MOORE AUTOMATION
Quick Quote
Fast response to complete part-number enquiries.
Global Delivery
Worldwide shipping options for industrial automation components.
Actual Product Verification
Current photos, nameplate images or inspection videos where available.
Technical Support
Support with product identification and installed-configuration verification.
CUSTOMER VOICES
Bought an ABB panel view from Moore last month but the signal light wouldn't turn on at first... They jumped on a video call with us immediately to guide us through troubleshooting. We talked through it a lot, but we finally got it fixed. Really fast and helpful after-sales support.
It was a very nice and good experience working with Moore. Specially with sales manager Sandy is very polite, skillful and knows everything about the product. Prices are very competitive, have big inventory of products with prompt lead time. Would like to work for a very long time.
Tel : +8618020776786
Whatsapp & Wechat : +8618020776786
Email : [email protected]
1 Year Warranty
