Model CC-TAOX01 identifies a 6-inch non-redundant Series C analog output IOTA listed for CC-PAOH01 and CC-PAOX01 in a 16-channel 4–20 mA output assembly.
Item NO.:
CC-TAOX01Brand/ Manufacturer:
HoneywellDimensions:
Verify exact assembly dimensions before installationWeight:
Not stated in the cited Honeywell product recordsCountry of Origin: :
Confirm on supplied product documentationDescription:
6-inch non-redundant analog output IOTAConfirm the exact product identity, connected hardware, field interface and current project release before installation.
Engineering note: Verify the 6-inch non-redundant arrangement, installed CC-PAOH01 or CC-PAOX01 IOM, terminal wiring, channel allocation and HART requirements before replacement.
Installation planning
Confirm CC-TAOX01 enclosure protection, cabinet airflow, mounting arrangement and documented temperature limits before installation.
Storage and handling
Keep CC-TAOX01 protected from moisture, contamination, impact and electrostatic discharge from receipt through installation.
Send the exact model, required quantity, destination and installed-hardware details. Request current nameplate photographs and confirm the required configuration before ordering.
A 6-inch non-redundant Series C analog output IOTA listed for CC-PAOH01 and CC-PAOX01, providing the field-termination interface for a 16-channel 4-20 mA output assembly.
Use the complete model, connected hardware and project definition when selecting a replacement. Physical similarity alone does not establish interchangeability.
Lifecycle assessment from the cited manufacturer evidence: Honeywell Experion Series C I/O Specification, EP03-490-520, Version 1.5 identifies the exact model or its documented hardware configuration, but the available source does not assign CC-TAOX01 a formal Active, Current, Mature, Discontinued or End-of-Life phase.
Ordering check: Confirm current stock, hardware revision, support status and exact replacement requirements with Tiffany before ordering.
These six checks apply to the exact installed assembly and should be completed against the current project documentation.
Record the selected IOM, HART requirement and loop-terminal assignment on the approved channel schedule.
For handover, retain measured loop current, readback deviation and the final actuator response for each commissioned output.
It is a 6-inch non-redundant analog output IOTA in Honeywell's Series C hardware family.
Honeywell lists CC-PAOH01 and CC-PAOX01 with this IOTA.
HART capability depends on the installed IOM. CC-PAOH01 supports HART; CC-PAOX01 is the non-HART analog output model.
The associated analog output IOMs provide 16 channels.
No. Honeywell identifies it as non-redundant. CC-TAOX11 is the listed redundant AO IOTA.
No. Confirm the exact model, IOM, channel function, redundancy requirement and terminal assignment.
Compare every terminal with the loop drawings, confirm polarity and field load, and verify that no unintended voltage is present.
Inspect connectors, keying, terminal condition, mounting hardware and model marking before fitting the IOM.
Perform controlled loop-current tests, verify output readback and alarms, and confirm each channel maps to the intended field device.
Not as a direct replacement. The two models represent non-redundant and redundant arrangements and require different cabinet and project designs.
Both PDFs are hosted on dcsmodule.com and prepared from the exact official manufacturer records cited on this page. They are independent Moore Automation references, not manufacturer-issued manuals.
Exact article identity, application context, procurement checks, replacement guidance and manufacturer-source trace.
OPEN SITE PDF → TECHNICAL DATAModel-specific specifications, compatibility boundaries, installation checks, commissioning guidance and official-source trace.
OPEN TECHNICAL DATA PDF →Ask for the exact CC-TAOX01 nameplate, 6-inch non-redundant format, connector and keying condition, field terminals, installed IOM details and packaging. Verify that the supplied unit carries the exact CC-TAOX01 identification.
| Specification | Official identification / verification note |
|---|---|
| Model | CC-TAOX01 |
| Hardware type | Analog output IOTA |
| Arrangement | Non-redundant |
| Width | 6 inches |
| Listed IOMs | CC-PAOH01 and CC-PAOX01 |
| Associated channel count | 16 channels through the installed IOM |
| Associated output type | 4-20 mA |
| HART availability | Available when paired with CC-PAOH01 |
Technical-data note: Values shown here are limited to the exact model and explicitly documented assembly. Confirm field conditions and the applicable project release before installation.
More from this brand · Browse by category
Same-brand Honeywell modules and I/O assemblies
Control and I/O hardware for related engineering work
Termination, carrier and interface product references
Verified condition-monitoring product references
Send the full CC-TAOX01 model, required quantity and delivery country. Our team can check current availability and arrange nameplate photos, packaging images or live/recorded video verification where available.
Confirm the exact model, available quantity, condition and estimated dispatch time.
Check the exact model, hardware identification, revision and visible product condition.
Receive quotation, warranty terms, delivery options and international shipping support.
Send the full model, quantity and destination for quotation and availability checking.
The Moore Automation team kept the sourcing process orderly and made the quotation details easy to compare.
Tiffany gave focused support throughout the inquiry and helped structure the compatibility questions for engineering review.
Tel : +8618020776786
Whatsapp & Wechat : +8618020776786
Email : [email protected]
1 Year Warranty
