PR6423/004-030 CON021 913-030 is an Emerson 8 mm Eddy Current Sensor System. Probe, cable, target material, gap and converter calibration must be checked as one measurement system.
Item NO.:
PR6423/004-030 CON02Order(MOQ):
1Product Origin:
Confirm with supplied unitLead Time：
2 daysBrand/ Manufacturer:
EmersonDimensions:
Not stated in exact-model evidenceWeight:
Not stated in exact-model evidenceCountry of Origin: :
Confirm with supplied unitDescription:
PR6423/004-030 CON021 913-030 | 8 mm Eddy Current Sensor SystemVERIFIED PRODUCT CONFIGURATION
PR6423/004-030 CON021 913-030 is an Emerson 8 mm Eddy Current Sensor System. The complete 12P1731X062 assembly marking must be retained and matched to the supplied unit. Verify the installed carrier, wiring, configuration and revision before replacement.
CONFIGURATION AT A GLANCE
System Configuration
Confirm the complete PR6423/004-030 CON021 913-030 marking, associated hardware, wiring and approved project records before replacement.
OFFICIAL PRODUCT FEATURES
DIRECT SALES CONTACT
Send the complete part number, required quantity, destination and installed configuration for quotation and availability checking.
PRODUCT OVERVIEW
PR6423/004-030 CON021 913-030 is an Emerson AMS/EPRO eddy-current measurement assembly built around the PR6423/004-030 8 mm non-contact sensor and the matched CON021/913-030 signal converter. The product manual emphasizes that the probe, extension connection, converter variant and complete suffix sequence form one measurement chain; visually similar components must not be assumed interchangeable. The system is intended to observe shaft or other conductive target movement without mechanical contact, so target material, probe mounting geometry, thread and connector arrangement, cable routing and the established mechanical gap all affect correct use. Before procurement, record the complete nameplates from both sensor and converter and compare them with the installed drawing and monitoring-system input requirements. During installation, protect the probe tip and cable, preserve routing and grounding, and avoid changing the established bracket geometry. Commissioning should verify the static gap, converter output, polarity, linear operating region and channel alarm behavior against the machine baseline. Country of origin: USA.
Manufacturer documentation: Emerson PR6423 sensor specification supports the applicable family and configuration checks; current lifecycle and supplied-unit status must be confirmed.
Important: Match PR6423/004-030 CON021 913-030, all suffixes, installed hardware, wiring and saved configuration before ordering.
Match PR6423/004-030, the cable length and CON021 913-030 converter as a calibrated system; do not qualify one component in isolation.
Compare thread, case style, mounting bracket and mechanical drawing with the installed point before removal.
Record shaft material, target geometry and the existing calibration basis because eddy-current scaling depends on the target system.
Use the applicable Emerson curve and site procedure, monitor converter output and set the mechanical gap within the approved linear region.
Do not substitute cable length or connector arrangement without confirming the complete calibrated chain and installation drawing.
Inspect the probe tip, cable armor, connectors, thread and converter label; record serials and visible damage before acceptance.
Verify gap voltage, dynamic response, polarity, monitor scaling and protection-system indications against the approved machinery test plan.
Provide the full probe and converter codes, cable routing, target material, mounting details, quantity and clear nameplate photographs.
OFFICIAL MANUFACTURER DOCUMENTS
Use the model-specific Moore Automation manual with the applicable Emerson reference. Match the exact installed configuration before replacement.
Two-page exact-model manual covering identification, configuration, application guidance and procurement checks.
OPEN PRODUCT MANUAL →MANUFACTURER REFERENCEManufacturer-controlled reference used for applicable product-family and configuration verification.
OPEN EMERSON REFERENCE →SEE THE ACTUAL PRODUCT BEFORE YOU BUY
Ask for current product photos, the complete installed nameplate, connections, housing details, packaging and visible condition. Verify that the supplied unit carries the exact PR6423/004-030 CON021 913-030 marking.
EMAIL : [email protected]WHATSAPP/WECHAT : +86-18020776786MODEL IDENTIFICATION
| Specification | Official identification / verification note |
|---|---|
| Manufacturer | Emerson |
| Product family | AMS / EPRO Eddy Current Measurement |
| Product type | 8 mm Eddy Current Sensor System |
| Catalog number | PR6423/004-030 CON021 913-030 |
| Specification | PR6423/004-030 CON021 913-030 |
| Sensor | PR6423/004-030 |
| Converter | CON021/913-030 |
| Probe diameter | 8 mm |
| Principle | Non-contact eddy current |
| Country of origin | USA |
SEE THE ACTUAL PRODUCT BEFORE YOU BUY
Ask for current product photos, the complete installed nameplate, connections, housing details, packaging and visible condition. Verify that the supplied unit carries the exact PR6423/004-030 CON021 913-030 marking.
EMAIL : [email protected]WHATSAPP/WECHAT : +86-18020776786WHY BUY FROM MOORE AUTOMATION
Quick Quote
Fast response to complete part-number enquiries.
Global Delivery
Worldwide shipping options for industrial automation components.
Actual Product Verification
Current photos, nameplate images or inspection videos where available.
Technical Support
Support with product identification and installed-configuration verification.
CUSTOMER VOICES
Bought an ABB panel view from Moore last month but the signal light wouldn't turn on at first... They jumped on a video call with us immediately to guide us through troubleshooting. We talked through it a lot, but we finally got it fixed. Really fast and helpful after-sales support.
It was a very nice and good experience working with Moore. Specially with sales manager Sandy is very polite, skillful and knows everything about the product. Prices are very competitive, have big inventory of products with prompt lead time. Would like to work for a very long time.
Tel : +8618020776786
Whatsapp & Wechat : +8618020776786
Email : [email protected]
1 Year Warranty
